定制各温度点温度响应速度快精密电热毯温控开关

RS-9700热保护器

RS-9700 Seies Themal Potecto

结构特点Featues o stuctue

RS-9700系列热保护器是由碟形高灵敏双金属元件、动触头、静触片、固定底座、外壳、耐温导线等组成。工作时双金属元件处于自由状态，动触头与静触片闭合，电路导通。当使用电器因故障发热而使温度上升至热保护器的动作温度时，双金属元件受热产生内应力而迅速动作，推开动触头离开静触片而断开电路，从而切断故障电器电源起到保护电器作用。当被保护电器温度下降到热保护器的额定复位温度值时，双金属元件恢复到初始状态触点闭合，电器恢复正常工作。该产品具有电阻小、感温快、动作迅速、安全可靠、体积小等优点。

RS-9700 seies themal potecto consists of dish shape high sensitive bimetallic elemeng,movable contact-head,static contact-piece,soleplate,oute case,ghemal esistant lead and so on.When opeation,the bimetallic element is in fee state and movable contact-head and static contace-piece ae closed and the cicuit is on.When the electic appliance is in opeation is in opeation and poduces heat caused by some toubles and tempeatue is aised to the ated action tempeatue of the poduct,the bimetallic element poduces inne stuess and acts quickly and pushes the movable contact-head and make the vontact point off and the powe supply is uned off the electic appliance stop.in this way the themal potection is made.When the tempeatue of electic appliance to be potected is dopped to the ated eset tempeatue.The bimetallic element estoes to its pimay state and contact point is closed .The electic appliance estoes its wok.The poduct has many advantages such as small in esisto,puick in tempeatue feeling,fast in action.Safe and eliable.compact and so on.

应用范围Poduct application

适用于各种家用电器和电子产品。如马达、日光灯镇流器、电池充电器、变压器、园筒形线圈、电蒸气浴机、电热水器、办公自动化设备等的过热保护。

Be applicable to all kinds of home appliances and electonics poducts. Such as Electic Motos,Fluoescent Ballasts,Battey Chages,Tansfomes,Solenoids,Heating pads,OA-Machines ETC.

额 定 电 压 Rated Voltage :AC250V/AC125V;

额 定 电 流 Rated Cuent:1~10

常态电气强度 Electic intensity:﹥800V

常态接触电阻 Contact esistance:﹤30m?

绝 缘 电 阻 Lnsulation esistance: ﹥100M?

响 应 速 度 Response speed:≦1℃/min

寿 命 次 数 Numbe of automatic cycles: ﹥6000(阻抗负荷Resistive Load)

温度检测方法：将试样两引线分别接在测试设备的夹具上，通上10mA左右的电流（不超过100mA），用一发光二极管指示电流的通断，然后将试样放入专用测温设备内，（测试设备内温度应均匀，加热升温速度可控制）温度计探头应贴近试样，控制检测设备温度以0.5～1℃/min的速率升温,当发光二极管熄灭时,记下温度计读数即为试样的动作温度。

TEST METHOD:Sample is connected to the fixtue of the equipment,and placed into the test equipment (Hot cuent of ai in the space of test should be equipped with a stie and tempeatue is contollable).A detect cuent about 10mA(no moe then 100mA)is passed though the sample and a themomete is placed junction to the sample to monito the opening tempeatue .The tempeatue of the test equipment is aised at the ate of 0.5～1℃ pe minute until the sample functioned